Laser Pro Park - Single Head Kit
Does the unit use frequencies which are allowed in the US?
Yes, the system uses the license free 904nm and although interference with other equipment cannot be ruled out, in the unlikely event of other laser based systems working in close proximity, the system has been designed to switch itself off. The system should be used for the purpose it was developed and not for other purposes.
Which reflective surfaces provide better detection distances?
The brighter the surface, the further the distance the Laser Pro Park will detect – up to 15 feet away. Parking in one's own garage, for example, we recommend you test with different material in front of the vehicle.
Can the Laser Pro Park cause damage to the human eye?
The unit is a Class 1 laser and meets all safety requirements under CFR 21 parts 1040.10 and 1040.11. It is low power and safe but we recommend you do not look into the lens of the unit at any time.
The Junction Box has 2 inputs – does it make any difference which port I connect the laser Sensor to?
Plug in to any of the ports.
Can I buy an additional sensor for the front or rear of the vehicle?
Yes additional Laser Sensor Heads are available.
The LED is distracting. Can I turn it off?
The LED is not required and may be turned off. Please review the instructions in the product manual for "Dark Mode."
The lens on the front of the unit has been damaged. Can it be replaced?
Yes. We suggest you disconnect the Laser Sensor head from the the Junction Box and contact the dealer you purchased the unit from or Laser Protector USA to arrange to have the product returned for repair. Alternatively, you may purchase a replacement lens and fit this yourself.
How do I test the unit and can it be triggered by a TV remote control?
No a TV remote control will not trigger the system. The unit has been designed to prevent unnecessary false alerts. The system performs a self check on power up – two audible beeps followed by flashing green LED.
Place a piece of paper over the lens and this should trigger the device into alert.
The unit has stopped working and doesn't go through the start-up procedure, what should I do?
Check to see if the ON / OFF switch has been switched to OFF. Check to see if the mute button has been pressed. Locate the Junction box and check the 1A fuse inside the Junction box.
If you need a new fuse, please contact your supplier or Laser Protector USA for assistance.
Yes, the system uses the license free 904nm and although interference with other equipment cannot be ruled out, in the unlikely event of other laser based systems working in close proximity, the system has been designed to switch itself off. The system should be used for the purpose it was developed and not for other purposes.
Which reflective surfaces provide better detection distances?
The brighter the surface, the further the distance the Laser Pro Park will detect – up to 15 feet away. Parking in one's own garage, for example, we recommend you test with different material in front of the vehicle.
Can the Laser Pro Park cause damage to the human eye?
The unit is a Class 1 laser and meets all safety requirements under CFR 21 parts 1040.10 and 1040.11. It is low power and safe but we recommend you do not look into the lens of the unit at any time.
The Junction Box has 2 inputs – does it make any difference which port I connect the laser Sensor to?
Plug in to any of the ports.
Can I buy an additional sensor for the front or rear of the vehicle?
Yes additional Laser Sensor Heads are available.
The LED is distracting. Can I turn it off?
The LED is not required and may be turned off. Please review the instructions in the product manual for "Dark Mode."
The lens on the front of the unit has been damaged. Can it be replaced?
Yes. We suggest you disconnect the Laser Sensor head from the the Junction Box and contact the dealer you purchased the unit from or Laser Protector USA to arrange to have the product returned for repair. Alternatively, you may purchase a replacement lens and fit this yourself.
How do I test the unit and can it be triggered by a TV remote control?
No a TV remote control will not trigger the system. The unit has been designed to prevent unnecessary false alerts. The system performs a self check on power up – two audible beeps followed by flashing green LED.
Place a piece of paper over the lens and this should trigger the device into alert.
The unit has stopped working and doesn't go through the start-up procedure, what should I do?
Check to see if the ON / OFF switch has been switched to OFF. Check to see if the mute button has been pressed. Locate the Junction box and check the 1A fuse inside the Junction box.
If you need a new fuse, please contact your supplier or Laser Protector USA for assistance.
Attributes
Loudness of warning sound: 85dB
Wavelength: 904 nm
Laser class: Class 1M
Wiring Loom: On/Off switch, Mute button, LED, piezo warning speaker
Duration of Self Diagnostic
1 sec during every activation (red and green LED light up and speaker sounds)
Indication of Functionality
Bi color LED blinks every 1 sec to visually confirm operating status. Bleeping of the parking sensor should an object be within 15 feet (depending on the reflectivity of the object).
Operation
• Start mode - first few seconds after activation - self diagnostic
• Search mode - lasts until detection of LIDAR laser beam
• Alert mode - upon detection of laser signal – reflected from own laser sensor or in the unlikely event of other laser based systems using the 904nm frequency in close proximity
Programming
The unit is factory set to alert the user should the laser sensor detect other laser based systems operating on the same 904nm frequency. To prevent interference the unit is designed to switch itself of after 8 seconds and then reboot 60 seconds later. If the user requires permanent protection rather than the factory set 8 seconds, the user needs to switch this function on.
Testing the System
The system performs a self test on power up. Thereafter the unit will pulse green every second to show correct operation. Should the unit fail at any time you will be notified by a continuous audible tone and red LED. The unit can be tested by placing a piece of paper close to the lens and moving it towards the sensor.
Accessories
Additional Laser Sensor heads. The unit is supplied with one laser sensor but the junction box can accommodate an additional laser sensor. Please contact your supplier should you need an additional sensor fitted. For the latest range of accessories please visit your local authorized reseller or Laser Protector USA's website.
General
Please note the detection distance can vary from 0 – 15 feet and depends on the reflective properties of the object immediately in front of the vehicle. The more reflective (e.g. brighter colors), the further the detection distance. The system must not be relied upon entirely when parking your vehicle as there can be no substitute for good judgement.
Use Extreme Caution
The Laser Sensor emits invisible laser radiation which may be harmful to the human eye. Please take particular caution when fitting the unit. Under no circumstances should you look directly at the device while the unit is switched on or connected to a live power supply.
Disclaimer
The manufacturer and/or its suppliers cannot be held responsible for system malfunction and any consequential damage. From time to time clean the front of the lens and check for damage. To prevent possible damage to the eye please avoid looking into the front of the lens.
Specifications subject to change without notice.
Loudness of warning sound: 85dB
Wavelength: 904 nm
Laser class: Class 1M
Wiring Loom: On/Off switch, Mute button, LED, piezo warning speaker
Duration of Self Diagnostic
1 sec during every activation (red and green LED light up and speaker sounds)
Indication of Functionality
Bi color LED blinks every 1 sec to visually confirm operating status. Bleeping of the parking sensor should an object be within 15 feet (depending on the reflectivity of the object).
Operation
• Start mode - first few seconds after activation - self diagnostic
• Search mode - lasts until detection of LIDAR laser beam
• Alert mode - upon detection of laser signal – reflected from own laser sensor or in the unlikely event of other laser based systems using the 904nm frequency in close proximity
Programming
The unit is factory set to alert the user should the laser sensor detect other laser based systems operating on the same 904nm frequency. To prevent interference the unit is designed to switch itself of after 8 seconds and then reboot 60 seconds later. If the user requires permanent protection rather than the factory set 8 seconds, the user needs to switch this function on.
Testing the System
The system performs a self test on power up. Thereafter the unit will pulse green every second to show correct operation. Should the unit fail at any time you will be notified by a continuous audible tone and red LED. The unit can be tested by placing a piece of paper close to the lens and moving it towards the sensor.
Accessories
Additional Laser Sensor heads. The unit is supplied with one laser sensor but the junction box can accommodate an additional laser sensor. Please contact your supplier should you need an additional sensor fitted. For the latest range of accessories please visit your local authorized reseller or Laser Protector USA's website.
General
Please note the detection distance can vary from 0 – 15 feet and depends on the reflective properties of the object immediately in front of the vehicle. The more reflective (e.g. brighter colors), the further the detection distance. The system must not be relied upon entirely when parking your vehicle as there can be no substitute for good judgement.
Use Extreme Caution
The Laser Sensor emits invisible laser radiation which may be harmful to the human eye. Please take particular caution when fitting the unit. Under no circumstances should you look directly at the device while the unit is switched on or connected to a live power supply.
Disclaimer
The manufacturer and/or its suppliers cannot be held responsible for system malfunction and any consequential damage. From time to time clean the front of the lens and check for damage. To prevent possible damage to the eye please avoid looking into the front of the lens.
Specifications subject to change without notice.
